11-27
11-27
Baud rate, flow control and terminator ........................................................
11-27
11-29
11-30
*CLS — Clear Status Clear status registers and error queue ........................
12-3
*ESE <NRf> – Event Enable Program the standard event enable register ...
12-4
*ESE? – Event Enable Query Read the standard event register ....................
12-4
*ESR? – Event Status Register Query Read register and clear it ..................
12-6
*IDN? – Identification Query Read the identification code ..........................
12-7
*OPC – Operation Complete Set the OPC bit in the standard
event register after all pending commands are complete ............................
12-8
*OPC? – Operation Complete Query Place a “1” in the output
queue after all pending operations are completed .....................................
12-10
*RCL – Recall Return to setup stored in memory .......................................
12-11
*RST – Reset Return 2182 to *RST defaults ..............................................
12-12
*SAV – Save Save present setup in memory ...............................................
12-12
*SRE <NRf> – Service Request Enable Program service request
12-12
*SRE? – Service Request Enable Query Read service request
12-12
*STB? – Status Byte Query Read status byte register .................................
12-14
*TRG – Trigger Send bus trigger to 2182 ...................................................
12-15
*TST?– Self-Test Query Run self test and read result ................................
12-15
*WAI – Wait-to-Continue Prevent execution of commands until
previous commands are completed ...........................................................
12-16
SCPI Signal Oriented Measurement Commands
13-2
13-3
13-3
13-4
14
Summary of Contents for 2182
