JUKI LBH-1790AN Instruction Manual Download Page 61

Page: 61 / 88

– 58 –

No.

Item

Setting range

Edit unit

Initial value

K018

Pattern selection function under sewing mode

Ineffective/effective

–

Ineffective

K019

Thread trimming on the way in continuous stitching

Permitted/Prohibited

–

Permitted

K021

Release amount of bobbin thread trimmer at

the start of sewing

This item sets the amount of releasing the bobbin
thread trimmer at the start of sewing.

0 to 15

1 pulse

K022

Presser lifter speed

This item sets presser lifter speed.

1 to 3

–

K023

Work clamp error detecting position

E083

The height at which the work clamp height

error is detected is set.
* If it is set at zero (0), the error will not be detected.

0 to 10.0

0.1

7.5

K025

Selection of the shorter-thread remaining function

With or without the shorter-thread remaining function is selected
using this memory switch.

Without the

shorter-thread

remaining

function

K028

Setting of the holding power of Y-feed motor

Low

Medium

High

–

Low

Permitted

Prohibited

Ineffective

Effective

*1 : Do not change the setting.

With the shorter-thread

remaining function

(LBH-1790ABN)

Without the shorter-

thread remaining function

(LBH-1790AN)

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands