JUKI LBH-1790AN Instruction Manual Download Page 32

Page: 32 / 88

– 29 –

To continue performing sewing from

some point in sewing
Sewing motion stop status

Error display screen

is displayed.

1) Release the error.

Press RESET key

❸

to release the error.

Then step motion screen

is displayed.

2) Return the presser.

Press BACKWARD key

❼

-1

and the

presser returns stitch by stitch.
Press FORWARD key

❼

-2

and the

presser advances stitch by stitch. Return the
presser to the re-sewing position.

3) Start sewing again.

Depress the right side pedal and sewing starts again.

To perform re-sewing from the start
Sewing motion stop status

Error display screen

is displayed.

1) Release the error.

Press RESET key

❸

to release the error.

Then step motion screen

is displayed.

2) Return the presser to the sewing

product setting position.

Press again RESET key

❸

and the

presser returns to the sewing product setting
position.

3) Perform again the sewing work from

the start.

When stop switch

is pressed during sewing

operation, the sewing machine interrupts sewing
and stops. At this time, error display screen

displayed to inform that the stop switch is pressed.

* Existing number of stitches/total number of stitches

are displayed in section D.

* Existing sewing command is displayed in section E.

Kinds of commands are :

Sewing

command

Jump feed

command

Thread trimmer

command

Error No. Error pictograph

Knife command

7. Performing re-sewing

E C

❼

-1

❼

-2

❸

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands