JUKI LBH-1790AN Instruction Manual Download Page 75

Page: 75 / 88

– 72 –

6. Replacing the fuse

WARNING :

1. To avoid electrical shock hazards, turn OFF the power and open the control box cover after about

five minutes have passed.

2. Open the control box cover after turning OFF the power without fail. Then, replace with a new

fuse with the specified capacity.

❶

❷

1) Turn OFF the power with the power switch

after confirming that the sewing machine has
stopped.

2) Draw the power cord from the power receptacle

after confirming that the power switch is turned
OFF.

Then wait for more than 5 minutes.

3) Remove four screws fixing the rear cover of the

control box. Then slowly open the rear cover.

4) Grasp the glass section of the fuse to be re-

placed and remove it.

5) Use the fuse with the specified capacity.

❶

F1 fuse 5A

For DC+60V power protection

Fuse for power protection of pulse motor and AT
solenoid

❷

F2 fuse 2A

For DC+24V power protection

Fuse for power protection such as solenoid
valves and sensors

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands