JUKI LBH-1790AN Instruction Manual Download Page 12

Page: 12 / 88

– 9 –

(7) Installing the hook oil shield plate

Install hook oil shield plate

❶

onto bed base

❸

with setscrew

❷

Attach hook oil shield plate

❶

to the

bed base with the sewing machine

raised.

In addition, check to be sure that the

sewing machine does not interfere

with hook oil shield plate

❶

when

tilting/raising the former.

Adjust the mounting of the hook oil

shield plate

❶

to prevent scattered

from the gap between the bed and

cover pot.

❶

❷

❸

(6) Connecting the machine head tilt detector

Connect machine head tilt detector

❶

with

connector

❷

located on the machine head

side.

(8) Installing the operation panel

Fix operation panel

❶

on the table with four wood-

screws

❷

. Pass the cable through hole

❸

in the

table.

❶

❷

❶

❷

❸

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands