JUKI LBH-1790AN Instruction Manual Download Page 80 | Manualshive

Page: 80 / 88

background image

– 77 –

Error code

Description

How to recover

Place of recovery

E492

Presser size over of basting

When stitching data of basting exceeds presser size.

Possible to re-en-
ter after pressing
reset key.

(During individual sew-
ing/cycle sewing)
Sewing data edit
screen
[S040] Basting needle
entry compensation
(During continuous
sewing)
Standard screen

E493

Presser size over of tie stitching at sewing end

When stitching data of tie stitching at sewing end exceeds
presser size.

Possible to re-en-
ter after pressing
reset key.

(During individual sew-
ing/cycle sewing)
Sewing data edit
screen
[S067] Tie stitching at
sewing end width
(During continuous
sewing)
Standard screen

E494

Presser size over of tie stitching at sewing start

When stitching data of tie stitching at sewing start exceeds
presser size.

Possible to re-en-
ter after pressing
reset key.

(During individual sew-
ing/cycle sewing)
Sewing data edit
screen
[S064] Tie stitching at
sewing start width
(During continuous
sewing)
Standard screen

E495

Presser size error (Width direction : right only)

When stitching data exceeds the size of right only of width
direction of presser.

Possible to re-en-
ter after pressing
reset key.

(During individual sew-
ing/cycle sewing)
Sewing data edit
screen
[S003] Knife groove
width, right or [S006]
Ratio of right and left
shapes
(During continuous
sewing)
Standard screen

E496

Presser size error (Width direction : left only)

When stitching data exceeds the size of left only of width
direction of presser.

Possible to re-en-
ter after pressing
reset key.

(During individual sew-
ing/cycle sewing)
Sewing data edit
screen
[S004] Knife groove
width, left or [S006]
Ratio of right and left
shapes
(During continuous
sewing)
Standard screen

E497

Presser size error (Length direction : front)

When stitching data exceeds the size of front of length
direction of presser.

Possible to re-en-
ter after pressing
reset key.

Standard screen

E498

Presser size error (Width direction : right and left)

When stitching data exceeds the size of both right and left
of width direction of presser.

Possible to re-en-
ter after pressing
reset key.

(During individual sew-
ing/cycle sewing)
Sewing data edit
screen
[S005] Overedging
width, left
(During continuous
sewing)
Standard screen

«
...
78
79
80
81
82
...
»

Summary of Contents for LBH-1790AN

























































































Reviews:

No comments

Related manuals for LBH-1790AN

Brand: Necchi Pages: 60

Brand: Singer Pages: 32

SONIC DUO SP600Q

Brand: Shark Pages: 20

Brand: Altrad Belle Pages: 46

SureBind System One

Brand: GBC Pages: 34

Brand: Oki Pages: 91

Brand: JUKI Pages: 34

Brand: Brotech Pages: 24

Brand: SSS Siedle Pages: 16

Brand: Dustbane Pages: 8

Brand: Dustbane Pages: 20

Brand: ABAC Pages: 148

Z44 New Millennium

Brand: Grace Pages: 22

Brand: Taski Pages: 32

Brand: AT&T Pages: 97

Brand: Singer Pages: 4

Brand: TAJIMA Pages: 35

Brand: Baby Lock Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands