JUKI LBH-1790AN Instruction Manual Download Page 31

Page: 31 / 88

– 28 –

Needle thread tension can be changed while performing trial sewing since the data related to the needle

thread tension can be set by the sewing mode as well.

1) Call thread tension at parallel section

setting data.

When THREAD TENSION key

is pressed,

the sewing data edit screen

is displayed.

2) Change thread tension at parallel

section.

Press DATA CHANGE key

❼

, and set

value

goes up or comes down and the thread

tension can be changed. The relation between the

finish of sewing and the set value is as shown in

the illustration below. Set the value referring to the

illustration.

3) Call thread tension at bar-tacking

section setting data.

When THREAD TENSION key

is pressed

again, the sewing data edit screen

is displayed.

4) Changing the needle thread tension at

bar-tacking section.

Press DATA CHANGE key

❼

, and set

value

goes up or comes down and the thread

tension can be changed. The relation between the

finish of sewing and the set value is as shown in

table below. Set the value referring to the table.
* For the tension other than that at parallel section

and bar-tacking section, refer to

"V-11. Chang

ing sewing data" p.34

and

"V-21. Method of

changing memory switch data" p.54

For the eyelet

radial shape, set

the bar-tacking

tension first to

approximately 120

and make the bal-

ance of stitches.

Set value of tension at

①

parallel section and

②

bar-tacking section

Purl stitch and Whip stitch

Purl stitch

When applying higher tension to the needle thread to permit it to pass straight

through fabric, the purl stitch is formed by the bobbin thread which is pulled

over from both sides to the center line.

Whip stitch

The whip stitch is formed in zigzag showing the needle thread only on top of

fabric, and the bobbin thread on the bottom.

Whip stitch

Purl stitch

Set value on panel

Initial value

Purl stitch

①

Tension at parallel

section

Crest is

lowered.

120

Crest is raised.

②

Bar-tacking tension

Thread tension

is decreased.

Thread tension is

increased.

Whip stitch

③

Tension at parallel

section

Thread tension

is decreased.

Thread tension is

increased.

④

Bar-tacking tension

Thread tension

is decreased.

Thread tension is

increased.

6. Changing needle thread tension

Whip stitch

❼

）、

）

）、

）

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands