JUKI LBH-1790AN Instruction Manual Download Page 73

Page: 73 / 88

– 70 –

Loosen nut

❶

and adjust the position with stopper

spring

❷

so that the distance from the front end of

machine bed to bobbin presser

❸

is 9.5 to 15 mm

when the sewing machine stops. Then tighten nut

❷

❶

❷

❸

3. Adjusting the presser bar pressure

4. Adjustment of the bobbin presser unit

9.5 to 15 mm

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the fol

lowing work after turning the power off and ascertaining that the motor is at rest.

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the fol

lowing work after turning the power off and ascertaining that the motor is at rest.

The presser bar pressure should be set on a pattern-by-pattern basis.

1) Set the mode to the input mode.

Under the input mode where SET READY LED

goes out, change of the pattern is enabled.
If the current mode is the sewing mode, press

READY key

❷

to change over the mode

to the input mode.

2) Invoke "S090 Presser bar pressure"

Press EDIT key

❽

. Then, press ITEM SE-

LECT key

❻

to select presser bar pressure

Increasing the set value of S090 will increase the
presser bar pressure to help prevent puckering.

❽

❼

❻

❷

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands