JUKI LBH-1790AN Instruction Manual Download Page 30

Page: 30 / 88

– 27 –

5. Performing pattern selection

(1) Selection from the pattern selection screen
1)

Set the mode to the input mode.

Under the input mode where SET READY LED

goes out, pattern selection is enabled.
If the current mode is the sewing mode, press

READY key

❷

to change over the mode

to the input mode.

Call the pattern selection screen.

Pattern No.

which is currently selected is

displayed.

Select the pattern.

Press DATA CHANGE key

❼

, and the

patterns which have been registered are changed
over in order and displayed. Here, select the No.
you desire to sew.

(2) Selection by means of the register key

For this sewing machine, it is possible to register a desired pattern No. to the PARAMETER REGISTER
key.
When the pattern is registered once, pattern selection can be performed by pressing only the switch.

→

Refer to

"V-16. Using parameter register key" p.46

❼

❷

Summary of Contents for LBH-1790AN

























































































Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands

JUKI LBH-1790AN, Instruction Manual

Search results

Summary of Contents for LBH-1790AN

Reviews:

Related manuals for LBH-1790AN

Brands by name

Popular brands