– 109 –
Button height (sewing flat/wrapped-around button with blindstitch)
This item sets the button holding height
(finished height) in the neck wrapping
process.
Button height (shank/marble)
This item sets the button holding height
(finished height) in the neck wrapping
process.
Button height (counter button)
This item sets the button holding height
(finished height) in the button sewing
process.
Number of stitches at the start of sewing of neck wrapping
This item sets the number of stitches at
the start of sewing of neck wrapping.
Number of stitches of tie stitch at the end of sewing of neck wrapping
This item sets the number of stitches of
tie stitch at the end of sewing in the neck
wrapping process.
Compensation of the button holding height at he time
of sewing flat/wrapped-around button with blindstitch
This item allows you to compensate the
button holding height at button sewing.
Thread release compensation
This item is the compensation value of the
button holding height in the button sewing
process. Sewing is performed in the neck
wrapping process by gradually returning
the compensation value to the former one.
This item is set when desiring to tightly wrap
up to the root of the button.
Button loader selection
<In case of shank/marble button>
: Loader OFF
: Loader ON
<In case of normal button>
: Loader OFF
: Loader ON
Number of times of wrapping
This item sets the number of times of
thread wrapping sewing in the neck
wrapping process.
Number of stitches of thread air-blow
This item sets the number of stitches of
thread air-blow in the neck wrapping process.
Compensation of button height in the neck
wrapping process
This item compensates the button holding
height in the neck wrapping process and
adjusts the wrapped condition.
No.
Item
Settomg range
Ddit unit
Initia display Remarks
0.5 to 15.0
0.1mm
2.5
0 to 15.0
0.1mm
3.4
0 to 20.0
0.1 mm
4.5
1 to 3
1 stitch
2
2 to 3
1 stitch
2
–5.0 to 5.0
0.1mm
–0.5
–5.0 to 5.0
0.1mm
0.5
– – –
– – –
Loader used
(Front side)
0 to 5
1 time
0
0 to 20
1 stitch
6
–5.0 to 5.0
0.1mm
0
Summary of Contents for AMB-289
