Intel UPI- 41A User Manual Download Page 13

Page: 13 / 69

UPI-41A/41AH/42/42AH USER’S MANUAL

The following section summarizes the functions of each UPI pin. NOTE that several pins have two or more
functions which are described in separate paragraphs.

Table 2-1. Pin Description

Symbol

Pin No.

Type

Name and Function

– D

12 – 19

I/O

DATA BUS:

Three-state, bidirectional DATA BUS BUFFER

(BUS)

lines used to interface the UPI-41A/41AH/42/42AH
microcomputer to an 8-bit master system data bus.

– P

27-34

I/O

PORT 1:

8-bit, PORT 1 quasi-bidirectional I/O lines.

– P

21-24

I/O

PORT 2:

8-bit, PORT 2 quasi-bidirectional I/O lines. The lower

35 – 38

4 bits (P

– P

) interface directly to the 8243 I/O expander

device and contain address and data information during PORT
4 – 7 access. The upper 4 bits (P

– P

) can be programmed

to provide interrupt Request and DMA Handshake capability.
Software control can configure P

as Output Buffer Full

(OBF) interrupt, P

as Input Buffer Full (IBF) interrupt, P

DMA Request (DRQ), and P

as DMA

ACKnowledge (DACK).

WRITE:

I/O write input which enables the master CPU to write

data and command words to the UPI INPUT DATA BUS
BUFFER.

READ:

I/O read input which enables the master CPU to read

data and status words from the OUTPUT DATA BUS BUFFER
or status register.

CHIP SELECT:

Chip select input used to select one UPI-

41A/41AH/42/42AH microcomputer out of several
connected to a common data bus.

COMMAND/DATA SELECT:

Address input used by the

master processor to indicate whether byte transfer is data
(A

0) or command (A

1).

TEST 0,

TEST INPUTS:

Input pins can be directly tested using

TEST 1

conditional branch instructions.

FREQUENCY REFERENCE:

TEST 1 (T

) also functions as

the event timer input (under software control). TEST0 (T

) is

used during PROM programming and verification in the UPI-
41A/41AH/42/42AH.

XTAL 1,

INPUTS:

Inputs for a crystal, LC or an external timing signal to

XTAL 2

determine the internal oscillator frequency.

SYNC

OUTPUT CLOCK:

Output signal which occurs once per UPI

instruction cycle. SYNC can be used as a strobe for external
circuitry; it is also used to synchronize single step operation.

EXTERNAL ACCESS:

External access input which allows

emulation, testing and PROM/ROM verification.

PROG

I/O

PROGRAM:

Multifunction pin used as the program pulse input

during PROM programming.
During I/O expander access the PROG pin acts as an
address/data strobe to the 8243.

RESET

RESET:

Input used to reset status flip-flops and to set the

program counter to zero. RESET is also used during PROM
programming and verification.

SINGLE STEP:

Single step input used in conjunction with the

SYNC output to step the program through each instruction.

POWER:

5V main power supply pin.

POWER:

5V during normal operation.

25V for UPI-41A,

21V for UPI-42 programming operation,

12V for

programming, UPI-41AH/42AH. Low power standby pin in
ROM version.

GROUND:

Circuit ground potential.

Summary of Contents for UPI- 41A





































































Search results

Summary of Contents for UPI- 41A

Reviews:

Related manuals for UPI- 41A

Brands by name

Popular brands

Intel UPI- 41A, User Manual

Search results

Summary of Contents for UPI- 41A

Reviews:

Related manuals for UPI- 41A

Brands by name

Popular brands