Intel UPI- 41A User Manual Download Page 58 | Manualshive

Page: 58 / 69

background image

UPI-41A/41AH/42/42AH USER’S MANUAL

231318 – 30

Figure 4-3. Latching Port Data

Timing

The sequence of single-step operation is as follows:

1) The processor is requested to stop by applying a low

level on SS. The SS input should not be brought low
while SYNC is high. (The UPI samples the SS pin in
the middle of the SYNC pulse).

2) The processor responds to the request by stopping

during the instruction fetch portion of the next in-
struction. If a double cycle instruction is in progress
when the single-step command is received, both cy-
cles will be completed before stopping.

3) The processor acknowledges it has entered the

stopped state by raising SYNC high. In this state,
which can be maintained indefinitely, the 10-bit ad-
dress of the next instruction to be fetched is preset
on PORT 1 and the lower 2 bits of PORT 2.

4) SS is then raised high to bring the processor out of

the stopped mode allowing it to fetch the next in-
struction.The exit from stop is indicated by the proc-
essor bringing SYNC low.

5) To stop the processor at the next instruction SS must

be brought low again before the next SYNC pulseÐ
the circuit in Figure 4-1 uses the trailing edge of the
previous pulse. If SS is left high, the processor re-
mains in the ‘‘RUN’’ mode.

Figure 4-1 shows a schematic for implementing single-
step. A single D-type flip-flop with preset and clear is
used to generate SS. In the RUN mode SS is held high
by keeping the flip-flop preset (preset has precedence
over the clear input). To enter single-step, preset is re-
moved allowing SYNC to bring SS low via the clear
input. Note that SYNC must be buffered since the
SN7474 is equivalent to 3 TTL loads.

The processor is now in the stopped state. The next
instruction is initiated by stoppe state. The next instruc-
tion is initiated by clocking ‘‘1’’ the flip-flop. This ‘‘1’’
will not appear on SS unless SYNC is high (I.e., clear
must be removed from the flip-flop). In response to SS
going high, the processor begins an instruction fetch
which brings SYNC low. SS is then reset through the
clear input and the processor again enters the stopped
state.

54

«
...
56
57
58
59
60
...
»

Summary of Contents for UPI- 41A






































































Reviews:

No comments

Related manuals for UPI- 41A

Professional Series

Brand: PACOM Pages: 15

Brand: Omnia Pages: 102

Brand: Paradox Pages: 4

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

Brand: Vivotek Pages: 136

Brand: BSS Audio Pages: 20

Brand: Reeven Pages: 2

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

5200 Live Series EventCD

Brand: MF DIGITAL Pages: 21

Brand: Z3 Technology Pages: 22

Brand: ExtraHop Pages: 3

Brand: Xilinx Pages: 36

Brand: Enterasys Pages: 5

Brand: c Pages: 32

ST7-EMU3 Series

Brand: ST Pages: 39

Brand: AMD Pages: 10

Brand: SeaLevel Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands