Intel UPI- 41A User Manual Download Page 6

Page: 6 / 69

UPI-41A/41AH/42/42AH USER’S MANUAL

All UPI’s have the following main features:

8-bit CPU

8-bit data bus interface registers

Interval timer/event counter

Two 8-bit TTL compatible I/O ports

Resident clock oscillator circuits

The UPI family has the following differences:

Table 1-2

UPI-41A

UPI-42

UPI-41AH

UPI-42AH

1K x 8 EPROM

2K x 8 EPROM

1K x 8 ROM

2K x 8 ROM

or 1K x 8 OTP

2K x 8 OTP

64 x 8 RAM

128 x 8 RAM

256 x 8 RAM

Set Security Feature

Signature Row Feature

32 Bytes with:
1. Test Code/Checksum
2. Intel Signature
3. Security Byte
4. User Signature

PROGRAMMING

UPI-41A

UPI-42

UPI-41AH/UPI-42AH

25V

21V

12.5V

50 ms

50 mA

30 mA

21.5V – 24.5V

18V

12.5V

21.5V – 24.5V

18V

20.V – 5.5V

TPW

50 ms

1 ms

PIN DESCRIPTION

UPI-41A/UPI-42

UPI-41AH/UPI-42AH

(T1)

T1 functions as a test input which can be

T1 functions as a test input that can be directly

directly tested using conditional branching

tested using conditional branching instructions. It

instructions. It functions as the event timer input

works as the event timer input under software

under software control.

control. It is used during sync mode to reset the
instruction state to S1 and synchronize the
internal clock to phase 1.

(SS)

Single step input used with the sync

Single step input used with the sync output to

output to step the program through each

step the program through each instruction.

instruction.

This pin is used to put the device in sync mode by
applying

12.5V to it.

Port 1 (P10 – P17): 8-bit, Quasi-Bidirectional I/O

Lines.

Lines. P10 – P17 access the Signature Row and
Security Bit.

NOTES:

For a complete description of the Security Feature, refer to the UPI-41AH/42AH Datasheet.

For a complete description of the Signature Row, refer to the UPI-41AH/42AH Datasheet.

Summary of Contents for UPI- 41A





































































Search results

Summary of Contents for UPI- 41A

Reviews:

Related manuals for UPI- 41A

Brands by name

Popular brands

Intel UPI- 41A, User Manual

Search results

Summary of Contents for UPI- 41A

Reviews:

Related manuals for UPI- 41A

Brands by name

Popular brands