Intel 3200 Thermal/Mechanical Design Manual Download Page 3

Page: 3 / 58

Intel® 3210 and 3200 Chipset Thermal/Mechanical Design Guide

Contents

Introduction ..............................................................................................................7
1.1

Design Flow........................................................................................................8

1.2

Definition of Terms ..............................................................................................8

1.3

Reference Documents ..........................................................................................9

Packaging Technology ............................................................................................. 11
2.1

Non-Critical to Function Solder Joints ................................................................... 13

2.2

Package Mechanical Requirements....................................................................... 13

Thermal Specifications ............................................................................................ 15
3.1

Thermal Design Power (TDP) .............................................................................. 15

3.2

Thermal Specification......................................................................................... 15

Thermal Simulation ................................................................................................. 17

Thermal Metrology .................................................................................................. 19
5.1

MCH Case Measurement..................................................................................... 19
5.1.1

Supporting Test Equipment...................................................................... 19

5.1.2

Thermal Calibration and Controls.............................................................. 20

5.1.3

IHS Groove ........................................................................................... 20

5.1.4

Thermocouple Attach Procedure ............................................................... 22

Reference Thermal Solution..................................................................................... 35
6.1

Operating Environment ...................................................................................... 35

6.2

Heatsink Performance ........................................................................................ 35

6.3

Mechanical Design Envelope ............................................................................... 36

6.4

Thermal Solution Assembly................................................................................. 36
6.4.1

Extruded Heatsink Profiles ....................................................................... 37

6.4.2

Retention Mechanism Responding in Shock and Vibration............................. 38

6.4.3

Thermal Interface Material....................................................................... 38

6.4.4

Reference Thermal Solution Assembly Process............................................ 39

6.5

Reliability Guidelines.......................................................................................... 40

Thermal Solution Component Suppliers ................................................................... 43
A.1

Heatsink Thermal Solution.................................................................................. 43

Mechanical Drawings............................................................................................... 45

Figures

1-1

Thermal Design Process .......................................................................................8

2-1

MCH Package Dimensions (Top View)................................................................... 11

2-2

MCH Package Height.......................................................................................... 11

2-3

MCH Package Dimensions (Bottom View).............................................................. 12

2-4

Non-Critical to Function Solder Joints ................................................................... 13

2-5

Package Height ................................................................................................. 14

5-1

Omega Thermocouple ........................................................................................ 20

5-2

FCBGA7 Chipset Package Reference Groove Drawing.............................................. 21

5-3

IHS Groove on the FCBGA7 Chipset Package on the Live Board................................ 21

5-4

The Live Board on the Fixture Plate...................................................................... 22

5-5

Inspection of Insulation on Thermocouple............................................................. 23

5-6

Bending the Tip of the Thermocouple ................................................................... 23

5-7

Extending Slightly the Exposed Wire over the End of Groove ................................... 24

5-8

Securing Thermocouple Wire with Kapton* Tape Prior to Attach............................... 24

Summary of Contents for 3200



























































Search results

Summary of Contents for 3200

Reviews:

Related manuals for 3200

Brands by name

Popular brands

Intel 3200, Thermal/Mechanical Design Manual

Search results

Summary of Contents for 3200

Reviews:

Related manuals for 3200

Brands by name

Popular brands