Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 44 | Manualshive

Page: 44 / 68

background image

7 | Warning and error messages

INFICON

44 / 68

Contura® S400-Operating-instructions-jina91en1-09-(2001)

7 Warning and error messages

During operation, the display shows information that helps you operate the instrument.

Measurement values are displayed along with current unit modes, operating

instructions as well as warnings and error messages. The instrument is equipped with

extensive self-diagnostic functions. If the electronics detect a faulty state, the device

will show this as far as possible on the display and will interrupt operation.

Warnings

Warnings warn of instrument modes that can impair the accuracy of measurements.

To perform measurements, confirm active warnings with the “Clear” button.

Error messages

Errors are events that force the interruption of the operation. The error message

consists of a number and a descriptive text. Once you have found the cause for the

error continue operation by pressing the button "Clear".

Touchscreen

You will find an overview of possible errors and warnings on the touchscreen:

►

> Help > Errors and warnings

See also

2

Call active errors and warnings [

7.1 List of warning and error messages

Type

Notification

Possible sources of

error

Remedy

W102

Timeout during

communication with

EEPROM in the IO module

The EEPROM in the IO

module is defective or

not present

• Contact customer service

W104

One EEPROM parameter

has been initialized

A new parameter was

introduced by a

software update

• Confirm the warning message

• Check that the message does not appear

when you restart the device

• Check whether the factory settings

correspond with the new parameter of

your application

The EEPROM in the IO

module is defective

• Confirm the warning message

• Check if the message occurs each time

when you restart the device

• Contact customer service

«
...
42
43
44
45
46
...
»

Summary of Contents for Contura S400





































































Reviews:

No comments

Related manuals for Contura S400

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 76

Brand: CAME Pages: 80

Brand: Waters Pages: 2

Brand: Sanlien Pages: 42

Brand: Alpha Networks Pages: 11

Smart Home Monitoring

Brand: Rogers Pages: 20

Brand: EverFocus Pages: 12

Brand: RED SHIELD Pages: 25

Brand: Speco Pages: 104

Brand: USA Industries Pages: 4

IQ PANEL 2 PLUS

Brand: QOLSYS Pages: 2

Brand: Zumimall Pages: 24

Brand: D-MAX Pages: 47

Brand: XNET Pages: 17

Enforcer SM-407-5T

Brand: SECO-LARM Pages: 1

Brand: T'nB Pages: 21

LUPUSNIGHT-139HD

Brand: Lupus Pages: 11

Brand: Ningbo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands