Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 38

Page: 38 / 68

6 | Operation

INFICON

38 / 68

Contura® S400-Operating-instructions-jina91en1-09-(2001)

NOTICE

Data loss due to an aborted connection

► Do not switch off the device and do not remove the USB flash drive while the

software is being updated!

Copy the file into the main directory of a FAT32 formatted USB flash drive.

Connect the USB flash drive to the USB port on the device.

> Update > Update Basic Unit

At the top in the window the active software version of the basic unit is

shown.

If one or more versions of the software are on the USB flash drive the most

recent version is shown on the line below. If this is the same as the version

already installed the background is green, otherwise it is red.

In order to load the new software version, press on the button "Update".

After completion there is an automatic restart of the system.

6.6.3 Update the software in expert mode

> Update > Update Operating Unit > Experte

Software versions already available on the device are shown in a list.

Highlight any of the software versions as required and proceed to step 5.

Resetting to an older software version is possible.

If alternatively you want to add a new software version, connect a FAT32

formatted USB flash drive with the update file to one of the USB ports of the

device.

In order to load the new software version, press on

To activate the new version, select the desired list entry and press

After completion there is an automatic restart of the system.

6.7 Save user and product data

You can save all user and product data to a USB flash drive and restore whenever

necessary.

No backup of measurement data

When backing up user and product data no measurement data backup is performed.

To backup measurement data see "Transferring measurement data [

}

35]”.

Supervisor - rights

Insert a FAT32-formatted USB flash drive into a USB port on the device.

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands