Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 47

Page: 47 / 68

INFICON

Warning and error messages | 7

Contura® S400-Operating-instructions-jina91en1-09-(2001)

47 / 68

Type

Notification

Possible sources of

error

Remedy

E520-

Contura

Pressure too high

Leak in the valve block

• Check that the message does not appear

when you restart the device

• Contact customer service

Pump is defective

• Contact customer service

E530

Leak in measuring chamber

Chamber not closed

• Connect the measuring chamber during

the measurement

Large product with

gross leakage

• Repeat the measurement

Leak in the chamber

• Check the hose connections of the

measuring chamber

• Contact customer service

W540

Pressure too low

• Check filter and replace if necessary

• Contact customer service

E560

Leaking gasket

Target pressure not

reached

• Remove a large product with gross

leakage

• Check the hose connections of the

measuring chamber

• Check filter and replace if necessary

• Contact customer service

W561

Leak in the outer gasket

Contaminated chamber

seal

• Clean the chamber seal

Damaged chamber

seal

• Check the chamber seal and replace it if

necessary

Hose connection (B)

leaking

• Check the hose connection (B) and

replace it if necessary

Filter leaking

• Check filter and replace if necessary

Internal hose

connection leaking

• Contact customer service

W562

Leak in the valve block

Contaminated valve

block

• Repeat the measurement

• Contact customer service

Defective valve block

• Contact customer service

E564

Valve error

Valve sticking

• Repeat the measurement

Valve defective

• Contact customer service

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands