Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 11

Page: 11 / 68

INFICON

Installation | 4

Contura® S400-Operating-instructions-jina91en1-09-(2001)

11 / 68

4 Installation

4.1 Setup

• In order not to distort the measurement results, select a location where the

possible room temperature for the device is constant.

• In order not to block the exhaust opening on the lower part of the device, place the

feet of the unit on a firm even surface.

• To easily reach the power switch on the back of the device, ensure there is

sufficient free space behind the device.

• Do not expose the device to direct sunlight.

WARNING

Danger from moisture and electricity

Moisture entering the device can lead to personal injury due to electric shocks as well

as damage to property due to short circuiting.

► Only operate the device in a dry environment.

► Operate the device away from sources of liquid and moisture.

CAUTION

Risk of injury from lifting the heavy device

The device weighs approx. 54 kg and can slip out of your hands.

► Lift and transport the device only with two people.

► To lift get hold below the floor panel.

NOTICE

Material damage from overheated device

The device heats up during operation and can overheat without sufficient ventilation.

► Please note the technical specifications.

► Ensure sufficient ventilation, especially on the ventilation slots on the left and right

of the device: There should be free space in the front, to the rear and sides of the

unit of at least 10 cm.

► Keep heat sources away from the device.

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands