Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 45

Page: 45 / 68

INFICON

Warning and error messages | 7

Contura® S400-Operating-instructions-jina91en1-09-(2001)

45 / 68

Type

Notification

Possible sources of

error

Remedy

W106

Several EEPROM

parameters have been

initialized

A software update

introduced new

parameters

• Confirm the warning message

• Check that the message does not appear

when you restart the device

• Check whether the factory settings

comply with the new parameters of your

application

The EEPROM has

been replaced in the IO

module

• Confirm the warning message

• Check that the message does not appear

when you restart the device

• Check whether the factory settings

comply with the new parameters of your

application

The EEPROM in the IO

module is defective

• Confirm the warning message

• Check if the message occurs each time

when you restart the device

• Contact customer service

W110

Real-time clock was reset!

Please enter date and time

The real-time clock has

not been set

• Enter the correct date and time

• Check that the message does not appear

when you restart the device

The jumper for the

battery in the IO

module is not inserted

• Contact customer service

Battery is discharged or

defective in the IO

module

• Contact customer service

Real-time clock

defective

• Contact customer service

W127

Wrong bootloader version

The bootloader is not

compatible with

application

• Contact customer service

W151

No communication with

operating unit

A software update or a

parameter reset has

been executed

• Confirm the warning message

• Check that the message does not appear

when you restart the device

Internal connection

problem between the

basic unit and the

operating unit

• Contact customer service

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands