Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 53

Page: 53 / 68

INFICON

Cleaning and maintenance | 8

Contura® S400-Operating-instructions-jina91en1-09-(2001)

53 / 68

If it is necessary to remove the lower membrane support including the damaged

membrane, first pull both hoses from the bottom of the measuring chamber.

To detach a hose, first press the release ring on the end of the hose in the

direction of the adapter, so that the locking releases and you can remove the

hose. Then unscrew the 16 screws with a T25-TORX® screwdriver.

For repair, pack the membrane support, so that it is protected against damage

during transport.

Please do not hesitate to contact us and send a completed declaration of

contamination before sending anything to us, see also "Sending in the device

[

}

60]”.

Mounting the

diaphragm support

• If you sent a membrane support with a defective membrane to the manufacturer,

your diaphragm support with membrane and mesh was re-tensioned and leak

testing was performed. With an upper membrane support an additional new lip

seal also came.

• If you want to take precautions in the event of damage to a membrane, you can

purchase from the manufacturer of the device ready-tensioned upper and lower

replacement membrane supports. Note that the service life of stored membranes

reduced by opening the original packaging and due to light.

They feature a separate membrane support with an intact membrane.

To assemble the upper membrane support hold it with the screw holes above

the provided thread openings, and rotate the 16 screws with hand tight a T25-

TORX® screwdriver. Tighten crosswise with a torque of 5 Nm.

The assembly of the upper membrane support is possible in 2 directions.

To install the lower membrane support, insert the membrane support with the

screw holes over the provided thread holes. To do this thread the hose

connection through the boreholes in the lower membrane support. There is only

one mounting direction possible.

Rotate the 16 screws with a T25-TORX® screwdriver hand tight. Tighten

crosswise with a torque of 5 Nm.

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands