IEI Technology WAFER-LX User Manual Download Page 88

Page: 88 / 144

WAFER-LX

4 to 5 sec (D

EFAULT

)

3 to 4 sec

2 to 3 sec

1 to 2 sec

System BIOS Cacheable [Enabled]

The

System BIOS Cacheable

option allows the system BIOS to be cached in the L2 cache.

Disabled

System BIOS is not cached in the L2 cache

Enabled

EFAULT

)

System BIOS is cached in the L2 cache

Video BIOS Cacheable [Disabled]

The

Video BIOS Cacheable

option allows the video BIOS to be cached in the L2 cache.

Disabled

Video BIOS is not cached in the L2 cache

Enabled

EFAULT

)

Video BIOS is cached in the L2 cache

Memory Hole At 15M – 16M [Disabled]

The

Memory Hole At 15M – 16M

reserves the memory space between 15MB and 16MB for ISA

expansion cards that require a specified area of memory to work properly. If you are using older

ISA expansion cards, please refer to the documentation that came with the card to see if it is

necessary to reserve the space.

Disabled

EFAULT

)

Memory is not reserved for ISA expansion cards

Enabled

Memory is reserved for ISA expansion cards

4-23

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands