IEI Technology WAFER-LX User Manual Download Page 108

Page: 108 / 144

WAFER-LX

This

PWRON After PWR-Fail

option allows you to select the state the system will return to if there

is a power failure or power to the system is suddenly cut off.

Off

EFAULT

)

After the power returns the system will remain off.

After the power returns, the system will turn on

Former-Sts

After the power returns the system will return to its

original state. If it was off, it will remain off. If it was on,

it will turn on again.

Game Port Address [201]

The Game Port Address configuration option allows you to specify the game port address.

Disabled

When disabled, the onboard game port will be unable to

access any system resources and will in effect be

inaccessible.

201

EFAULT

)

The game board address is set to 201

209

The game board address is set to 209

4-43

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands