IEI Technology WAFER-LX User Manual Download Page 72

Page: 72 / 144

WAFER-LX

All, But Disk/Key

The system boot will not stop for a keyboard

or a disk error; it will stop for all other errors.

Base Memory:

The

Base Memory

is NOT user configurable. The POST will determine the amount of base (or

conventional) memory is installed in the system. The value of the base memory is typically 512K

for systems with 512K memory installed on the CPU card or 640K for systems with 640K or more

memory installed on the motherboard.

Extended Memory

The

Extended Memory

is NOT user configurable. The BIOS determines how much extended

memory is present during the POST. This is the amount of memory above 1MB located in the

memory address map of the CPU.

Total Memory

The

Total Memory

is NOT user configurable.

4-7

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands