IEI Technology WAFER-LX User Manual Download Page 105

Page: 105 / 144

WAFER-LX User Manual

BIOS Menu 13: Super I/O Device [Integrated Peripherals]

POWER ON Function [BUTTON ONLY]

The

POWER ON Function

option allows you to select the method you use to turn on the system.

Password

When you turn on the computer you will be

prompted for a password (see the

KB Power ON

Password option below

)

Hot KEY

You can use a pre-specified hot key to turn on

your computer (see the

Hot Key Power ON

option below)

Mouse Left

Click the left mouse button to turn the system on

Mouse Right

Click the right mouse button to turn the system on

Any KEY

Click any key to turn the system on

BUTTON ONLY

EFAULT

)

The computer can only be turned on with the

power button

Keyboard 98

If you are using Windows 98 or better and have

the appropriate keyboard, you can use the

keyboard's wake-up or power-on button to start up

the computer.

x KB Power ON Password [Enter]

The

KB Power ON Password

option can only be specified if you have selected the

Password

the

POWER ON Function

option. To set the password, place the cursor on the password option

and click “

NTER

.” You will be prompted to enter a password. Select you password and press

“

NTER

.” You will be asked to confirm the password. Confirm it and then press “

NTER

” and the

password will be set.

x Hot Key Power ON [Ctrl-F1]

The

Hot Key Power ON

option can only be specified if you have selected the

Hot KEY

as the

POWER ON Function

option. The following key combinations can be selected as the hot keys

that will turn your computer on.

1. Ctrl-F1

2. Ctrl-F2

4-40

IEI

Technology, Corp.

4-40

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands