IEI Technology WAFER-LX User Manual Download Page 104

Page: 104 / 144

WAFER-LX

Onboard LAN1/2 Boot Rom [Enabled]

The

Onboard LAN Boot Rom

allows you to boot your system from a LAN server. For this to be

possible the LAN card installed on your system must have boot ROM. If you choose to boot your

system from a server using the LAN boot ROM functionality, you do not need a boot disk installed

on the system.

Disabled

If disabled, you will not be able to boot your system

from a server.

Enabled

EFAULT

)

You will be able to boot your system from a server if the

LAN card installed in the system has boot ROM

Onboard LAN1/2 MacAddress contr [Enabled]

Disabled

Enabled

EFAULT

)

1.1.11

Super I/O Device

The

SuperIO Device

menu (

BIOS Menu 13

) allows you to change the super IO device

configurations.

4-39

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands