manualshive.com logo in svg

IEI Technology WAFER-LX, User Manual

Share
Download
IEI Technology WAFER-LX User Manual Download Page 37

 

WAFER-LX User Manual

 

 

10. CN10: PC/104 (104-pin ISA bus) Connector 

The WAFER-LX features a PC/104 expansion bus that let you attach any kind of PC/104 

modules. The PC/104 bus has already become the industrial embedded PC bus standard, so 

you can easily install over thousands of PC/104 modules from hundreds of vendors in the 

world. There are two PC-104 connectors on this board: PC/104-64 and PC/104-40.     

A -5V/-12V (-VCC) connector is provided to supply -VCC voltage that is routed through the 

PC/104 64-pin connector.       

Table 2-9 PC/104-64 

Connector 

Pinouts 

PIN 

DESCRIPTION 

PIN 

DESCRIPTION 

1 

IOCHECK# 33 

GROUND 

2 SD7 

34 IRSTDRV 

3 

SD6 35 

VCC 

4 SD5 

36 IRQ9 

5 SD4 

37 -5V 

6 

SD3 38 

DRQ2 

7 SD2 

39 -12V 

8 

SD1 40 

ZWS 

9 SD0 

41 +12V 

10 IOCHRDY 

42 GROUND 

11 AEN 

43 SMEMW# 

12 LA19 

44 SMEMR# 

13 LA18 

45 IOW# 

14 LA17 

46 IOR# 

15 SA16 

47 DACK3# 

16 SA15 

48 DRQ3 

17 SA14 

49 DACK1# 

18 SA13 

50 DRQ1 

19 SA12 

51 REFRESH# 

20 SA11 

52 SYSCLK 

21 SA10 

53 IRQ7 

22 SA9 

54 N/C 

23 SA8 

55 IRQ5 

 

2-16

2-16 

 

IEI

®

 Technology, Corp. 

Summary of Contents for WAFER-LX

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands