IEI Technology WAFER-LX User Manual Download Page 124

Page: 124 / 144

WAFER-LX User Manual

1. Introduction

The ALi M5283 is a highly integrated disk drive controller that is capable of managing Parallel-ATA

and Serial-ATA interface hard disk drives. The ALi controller supports PATA UDMA transfer mode

up to mode 6 and SATA 1.0 disk drives. The ALi M5283 also comes with cost-effective RAID

functionalities that can be used to increase data read/write speed and to provide protection to data

by distributing mirrored duplicates of data onto two disk drives (RAID1).

CAUTION!

You must properly configure the associated BIOS settings before the Ctlr+A

key combination can take effect. Please refer to

Chapter 4 Award BIOS

Setup,

the discussions of the associated configurations for more details.

SATA disk drive support must be initiated under the following two BIOS

sub-menus.

1. Boot -> Onboard SATA ROM

Chipset -> Southbridge Chipset Configuration

You will not be able to access the ALi configuration utility unless you have

properly initiated the SATA disk drive support in the Award BIOS configuration

utility.

CAUTION!

A configured RAID volume (which may consist of multiple hard drives)

appears to an operating system as a contiguous storage space. Your

operating system will not be able to distinguish the physical disk drives

contained in a RAID configuration.

Precautions:

1. One key benefit a RAID configuration brings you is that a single hard drive can fail within a

RAID array without damaging your data. With RAID1 array, you can replace a failed drive

and restore your RAID configuration.

C-2

IEI

Technology, Corp.

C-2

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands