manualshive.com logo in svg

IEI Technology WAFER-LX, User Manual

Share
Download
IEI Technology WAFER-LX User Manual Download Page 14

 

WAFER-LX User Manual 

 

Connectivity 

The WAFER-LX provides the following interface connections: 

Label 

Function 

CN1 

4P power connector 

CN2 

3-pin PS-ON/ATX feature connector 

CN3 

5-pin Inverter control 

CN4 

3-pin CPU fan connector 

CN5 

5-pin External LED connector (to chassis LED control PCB) 

CN6 

144-pin SDRAM SO-DIMM socket 

CN7 

2-pin connector to the external Lithium 3V coin cell battery- 

CN8 

10-pin audio connector (to the external adapter cable kit which 

should provide phone jacks for Line_out, Line_in, and MIC_in 

connectivity) 

CN9 

4-pin Audio CD_IN connector 

CN10 

PC/104 connector (104-pin ISA bus) 

CN11 

3-pin external VCC (supplementary for PC/104) power connector 

CN12 

2-pin Reset button switch (to the chassis front panel) 

CN13 

2-pin Power switch button (to the chassis front panel) 

CN14 

10-pin general purpose I/Os connector 

CN15 

26-pin parallel port pin header 

CN16 

14-pin internal serial port pin header (COM2) 

CN17 

6-pin keyboard/mouse connector (a 6-pin-to-PS/2 adapter cable is 

required) 

CN18 

Not implemented 

CN19 

External USB1.1 connector (2 ports) 

CN20 

10/100BaseT Ethernet port 

CN21 

10/100BaseT Ethernet port 

CN22 

External D-SUB 9 serial port connector (COM1) 

CN23 

Serial ATA connector 

CN24 

8-pin internal USB header (an adapter cable required) 

CN25 

Serial ATA connector 

 

1-4

1-4 

 

IEI

®

 Technology, Corp. 

Summary of Contents for WAFER-LX

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands