IEI Technology WAFER-LX User Manual Download Page 2

Page: 2 / 144

WAFER-LX

Revision History

Title

3.5” Profile WAFER-LX Embedded Board

Revision Number

Description

Date of Issue

1.0

Initial release

April, 2006

Copyright Notice

The information in this document is subject to change without prior notice in order to improve

reliability, design, and function and does not represent a commitment on the part of the

manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential

damages arising out of the use or inability to use the product or documentation, even if advised of

the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No

part of this manual may be reproduced by any mechanical, electronic, or other means in any form

without prior written permission of the manufacturer.

Trademarks

AMD is the registered trademarks of Advanced Micro Devices, Inc. Geode, GeodeLink, Virtual

System Architecture and 3DNow! are also trademarks of Advanced Micro Devices, Inc. AMI is a

registered trademark of American Megatrends Inc. Other product names mentioned herein are

used for identification purposes only and may be trademarks and/or registered trademarks of their

respective owners.

Page

Page

IEI

Technology, Corp.

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands