IEI Technology WAFER-LX User Manual Download Page 69

Page: 69 / 144

WAFER-LX User Manual

BIOS Menu 1: Award BIOS CMOS Setup Utility

NOTE:

The following sections will completely describe the menus listed below and

the configuration options available to users.

The following menu options are seen in

BIOS Menu 1

Standard CMOS Features:

Changes the basic system configuration.

Advanced BIOS Features:

Changes the advanced system settings.

Advanced Chipset Features:

Changes the chipset configuration features

Integrated Peripherals:

Changes the settings for integrated peripherals

Power Management Setup:

Allows you to configure power saving options

PCIPnP:

Changes the advanced PCI/PnP Settings

PC Health Status:

Menu that monitors essential system parameters

The following user configurable options are also available in the BIOS Main Menu

Load Fail-Safe Defaults

This option allows you to load failsafe default values for each of the parameters on the Setup

menus.

F6 key can be used for this operation on any page.

Load Optimized Defaults

This option allows you to load optimal default values for each of the parameters on the Setup

menus.

F7 key can be used for this operation on any page.

Set Supervisor Password

By default no

Supervisor Password

set. If you wish to install a supervisor password, select this

field and enter the password. After this option has been selected, a red dialogue box with

“Enter

Password: ”

will appear. You will be asked to confirm your password. Retype the original

password into the

“Confirm Password: ”

dialogue box and press enter.

Change User Password

By default no

User Password

set. If you wish to install a user password, select this field and

enter the password. After this option has been selected, A red dialogue box with

“Enter

4-4

IEI

Technology, Corp.

4-4

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands