IEI Technology WAFER-LX User Manual Download Page 109

Page: 109 / 144

WAFER-LX User Manual

PnP/PCI Configurations

The

PnP/PCI Configurations

menu (

BIOS Menu 9

) allows you to set the plug and play, and PCI

options.

BIOS Menu 14: PnP/PCI Configurations

Init Display First [PCI Slot]

The

Init Display First

option allows you to determine what display device to boot with.

PCI Slot

EFAULT

)

The system will boot using the PCI graphic card

Onboard

The system will boot using the preinstalled onboard graphics

device

Reset Configuration Data [Disabled]

The

Reset Configuration Data

option allows you to reset the Extended System Configuration

Data (ESCD) when you exit setup if you have problems booting the system up after you have

installed a new add-on.

4-44

IEI

Technology, Corp.

4-44

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands