IEI Technology WAFER-LX User Manual Download Page 77

Page: 77 / 144

WAFER-LX User Manual

Enabled

Activates automatically when the system boots up

causing a warning message to appear when anything

attempts to access the boot sector or HDD partition table.

Disabled

(Default)

No warning message will appear when anything attempts

to access the boot sector or HDD partition table.

NOTE:

Many disk diagnostic programs can cause the above warning message to

appear when the program attempts to access the boot sector table. If you

will be running such a program, it is recommended that you first disable the

virus protection function before hand.

CPU Internal (L1 & L2) Cache [Enabled]

The

CPU L1 & L2 Cache

option allows users to select whether the CPU primary cache (L1) and

secondary cache (L2) will be turned on or off.

Enabled

EFAULT

)

The L1 and L2 CPU caches are both turned on

Disabled

The L1 and L2 CPU caches are both turned off

Boot From LAN Control

This allows you to utilize the boot-from-LAN feature.

SATA Boot ROM Control

When enabled, the ALi or ULi SATA ROM management utility will provide the access to RAID
configuration utility during the POST stage and allow you to boot from SATA disk drives. You
may refer to

Appendix C

for more details. .

Boot Device

There are three

Boot Device

configuration options. They are:

First Boot Device

EFAULT

: Floppy]

Second Boot Device

EFAULT

: Hard Disk]

4-12

IEI

Technology, Corp.

4-12

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Brands by name

Popular brands