IEI Technology WAFER-LX User Manual Download Page 99

Page: 99 / 144

WAFER-LX User Manual

MODEM Use IRQ [3]

The

MODEM Use IRQ

option tells the power management which IRQ it should monitor for modem

wakeup. The following options can be selected.

1. N/A

2. 3

EFAULT

)

3. 4

4. 5

5. 7

6. 9

7. 10

8. 11

Suspend Mode [Disabled]

The

Suspend Mode

option allows you to specify how long the computer must wait for no activity

before it goes into a suspend mode. If you disable this option the system will not go into a suspend

mode. Note that if you selected max. or min. as the setting for the

Power Management

option,

you will not be able to configure this setting. The following settings can be made.

1. Disable

EFAULT

)

1 Min

2 Min

3 Min

4 Min

2. 8

Min

3. 12

Min

4. 20

Min

5. 30

Min

6. 40

Min

1 Hour

HDD Power Down [Disabled]

The

HDD Power Down

option allows you to specify how long the computer must wait for no

activity before the HDD powers down. If you disable this option the HDD will not power down. Note

4-34

IEI

Technology, Corp.

4-34

Summary of Contents for WAFER-LX

















































































































































Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands

IEI Technology WAFER-LX, User Manual

Search results

Summary of Contents for WAFER-LX

Reviews:

Related manuals for WAFER-LX

Brands by name

Popular brands