manualshive.com logo in svg

IEI Technology WAFER-LX, User Manual

Share
Download
IEI Technology WAFER-LX User Manual Download Page 26

 

WAFER-LX

Important Features 

Major functionalities provided by the WAFER-LX are listed below: 

Table 2-1 Important 

Features 

 

RoHS compliance. 

 

AMD long term support product; embedded AMD processor. 

 

PC/104 PCI-to-ISA extension slot for stack-up configurations 

 

CF II socket (CF card behaves as an IDE boot device if no HDD is 

applied). 

 

Embedded Graphics Controller with the support for VGA-interface and 

LVDS displays (simultaneous operation). 

 

Supports one dual-channel 18-bit (36-bit) TFT, and with up to 1920 x 1440 

resolutions 

 

Aluminum alloy heatsink for optimum heat dissipation in fan-less 

installations.   

 

Supports dual-channel 18-bit LVDS and/or 24-bit TFT LCD interface 

 

System Memory: one 144-pin SODIMM socket for 64-bit, 400MHz 

memory modules ranging from 64MB to 1GB in size. 

 

64KB I/ 64KB D L1 cache and 128KB L2 cache for fast I/O turnarounds 

 

Two serial ports, COM1 for RS-232, COM2/3 for RS-232/422/485 

 

USB compliant with the USB rev. 2.0 standard

 

 

System Chipset: AMD Geode LX-800 + Geode CS5536AD Southbridge 

 

Hardware Monitor: built-in to monitor CPU Vcore, VCC, CPU/System fan 

speed, and temperature detection functionalities.     

 

Independent DMA audio engines 

 

PXE LAN support with ATX power supply 

 

Realtek

®

 8100C: Supports 10/100BaseT Ethernet, IEEE 802.3U 

compatible full duplex flow control 

 

Audio: ALC203 AC”97 2.3 CODEC 

 

2-5

2-5

 

Summary of Contents for WAFER-LX

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands