IEI Technology IMB-Q870-i2 User Manual Download Page 210

Page: 210 / 223

IMB-Q870-i2 microATX Motherboard

Page 194

NOTE:

A firewall or a SELinux is not in use in the whole setup process

described above. If there is a firewall or a SELinux protecting the

system, modify the configuration information to accommodate them.

C.7 Other Information

C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller

When the system uses AHCI mode or some specific SATA controllers such as ALi M5283

or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key

recovery. Please follow the steps below to install the SATA RAID/AHCI driver.

Step 1:

Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into

a USB floppy disk drive. The SATA RAID/AHCI driver must be especially

designed for the on-board SATA controller.

Step 2:

Connect the USB floppy disk drive to the system.

Summary of Contents for IMB-Q870-i2
































































































































































































































Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands

IEI Technology IMB-Q870-i2, User Manual

Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands