IEI Technology IMB-Q870-i2 User Manual Download Page 129

Page: 129 / 223

IMB-Q870-i2 microATX Motherboard

Page 113

Enabled D

EFAULT

Detect if a non-compliance PCI Express device is

connected to the PCI Express port.

5.4.1.2 PCH Azalia Configuration

Use the

PCH Azalia Configuration

submenu (

BIOS Menu 20

) to configure the PCH

Azalia codec.

Chipset

PCH Azalia Configuration

Azalia (HD Audio)

[Enabled]

Control Detection of the
Azalia device.
Disabled=Azalia will be
unconditionally
disabled.
Enabled=Azalia will be
unconditionally
Enabled.

---------------------

ÅÆ

: Select Screen

↑

↓

: Select Item

Enter

Select

+ - Change Opt.
F1 General

Help

F2 Previous

Values

F3 Optimized

Defaults

Save & Exit

ESC Exit

BIOS Menu 20: PCH Azalia Configuration

Azalia [Enabled]

Use the

Azalia

option to enable or disable the High Definition Audio controller.

Disabled

The onboard High Definition Audio controller is disabled

Enabled D

EFAULT

The onboard High Definition Audio controller is detected

automatically and enabled

Summary of Contents for IMB-Q870-i2
































































































































































































































Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands

IEI Technology IMB-Q870-i2, User Manual

Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands