manualshive.com logo in svg

IEI Technology IMB-Q870-i2, User Manual

Share
Download
IEI Technology IMB-Q870-i2 User Manual Download Page 176

 

 

IMB-Q870-i2 microATX Motherboard

Page 160 

Step 3: 

Install operating system, drivers and system applications (see 

Section

 

C.2.3

) 

Step 4: 

Build the recovery partition (see 

Section

 

C.2.4

) or build the auto recovery 

partition (see 

Section C.3

) 

Step 5: 

Create factory default image (see 

Section

 

C.2.5

) 

S

te

p

 0

:

 

The detailed descriptions are described in the following sections.   

 NOTE: 

The setup procedures described below are for Microsoft Windows 

operating system users. For Linux, most of the setup procedures are 

the same except for several steps described in 

Section C.3

. 

C.2.1 Hardware and BIOS Setup 

Step 1: 

Make sure the system is powered off and unplugged. 

Step 2: 

Install a hard drive or SSD in the system. An unformatted and unpartitioned disk 

is recommended.   

Step 3: 

Connect an optical disk drive to the system and insert the recovery CD. 

Step 4: 

Turn on the system. 

Step 5: 

Press the <

DELETE

> key as soon as the system is turned on to enter the BIOS. 

Step 6: 

Select the connected optical disk drive as the 1

st

 boot device. (

Boot

 

Æ

 

Boot 

Device Priority

 

Æ

 

1

st

 Boot Device

). 

Step 7: 

Save changes and restart the computer. Continue to the next section for 

instructions on partitioning the internal storage.

  

S

te

p

 0

:

 

C.2.2 Create Partitions 

To create the system backup, the main storage device must be split into two partitions 

(three partitions for Linux). The first partition will be for the operating system, while the 

Summary of Contents for IMB-Q870-i2
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands