IEI Technology IMB-Q870-i2 User Manual Download Page 18

Page: 18 / 223

IMB-Q870-i2 microATX Motherboard

Page 2

1.1 Introduction

Figure 1-1: IMB-Q870-i2

The IMB-Q870-i2 is a microATX motherboard. It accepts a Socket LGA1150 Intel®

Core™ i7, Core™ i5, Core™ i3, Pentium® or Celeron® processor and supports four

240-pin 1333/1066 MHz dual-channel DDR3 DIMM modules up to 32.0 GB maximum.

The IMB-Q870-i2 includes VGA, HDMI, and DVI-D display ports for triple independent

display. Expansion and I/O include one PCI slot, one PCIe x16 slot, one PCIe x4 slot with

x1 signal, one PCIe x1 slot, two USB 3.0 ports on the rear panel, two USB 3.0 ports by pin

header, four USB 2.0 on the rear panel, four USB 2.0 by pin header, four SATA 6Gb/s

connectors, six COM ports, and two keyboard/mouse connectors.

1.2 Benefits

Some of the IMB-Q870-i2 motherboard benefits include:

Powerful graphics with multiple monitors

Staying connected with both wired LAN connections

Speedy running of multiple programs and applications

Summary of Contents for IMB-Q870-i2
































































































































































































































Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands

IEI Technology IMB-Q870-i2, User Manual

Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands