IEI Technology IMB-Q870-i2 User Manual Download Page 81

Page: 81 / 223

IMB-Q870-i2 microATX Motherboard

Page 65

Figure 4-11: Flash Descriptor Security Override Jumper Location

4.3.4 PCIe x16 Interface Setup

The PCIe x16 interface setup is made through the BIOS options in “Chipset

PCH-IO

Configuration” BIOS menu. Use the

PCIEX16 Power

option to configure the PCIe x16

channel mode.

BIOS Options

Description

1 x16 PCIE

Sets the PCIe x16 slot as one PCIe x16. (Default)

Table 4-2: PCIe x16 Interface Setup

Please refer to

Section 5.4.1

for detailed information.

4.3.5 USB Power Select

The USB power selection is made through the BIOS options in “Chipset

PCH-IO

Configuration” BIOS menu. Use the

USB SW1 Power

and the

USB SW2 Power

BIOS

options to configure the power source to the corresponding USB ports (see

Table 4-3

BIOS Options

Configured USB Ports

USB SW1 Power

K/M_USB1 (external USB 2.0 ports)

LAN1_USB1 (external USB 3.0 ports)

Summary of Contents for IMB-Q870-i2
































































































































































































































Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Brands by name

Popular brands

IEI Technology IMB-Q870-i2, User Manual

Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Brands by name

Popular brands