IEI Technology IMB-Q870-i2 User Manual Download Page 111

Page: 111 / 223

IMB-Q870-i2 microATX Motherboard

Page 95

Disabled D

EFAULT

Disable ME unconfigure

Enabled

Enable ME unconfigure

5.3.8 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 10

) to read USB configuration

information and configure the USB settings.

Advanced

USB Configuration

USB Devices:
1 Keyboard, 2 Hubs

Legacy USB Support

[Enabled]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.

---------------------

ÅÆ

: Select Screen

↑

↓

: Select Item

Enter

Select

+ - Change Opt.
F1 General

Help

F2 Previous

Values

F3 Optimized

Defaults

Save & Exit

ESC Exit

BIOS Menu 10: USB Configuration

USB Devices

The

USB Devices Enabled

field lists the USB devices that are enabled on the system

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

Summary of Contents for IMB-Q870-i2
































































































































































































































Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Brands by name

Popular brands

IEI Technology IMB-Q870-i2, User Manual

Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Brands by name

Popular brands