manualshive.com logo in svg

IEI Technology IMB-Q870-i2, User Manual

Share
Download
IEI Technology IMB-Q870-i2 User Manual Download Page 79

 

 

IMB-Q870-i2 microATX Motherboard 

Page 63

Step 5: 

Removing the iRIS-2400 module

. To remove the iRIS-2400 module, push both 

handles outward. The module is ejected by a mechanism in the socket.

Step 0:

 

 NOTE: 

After installing the iRIS-2400 module, use 

LAN2

 port to establish a 

network connection. Please refer to 

Section  4.7

 for IPMI setup 

procedures.  

 

4.3 System Configuration 

The system configuration is controlled by buttons, switches and BIOS options. The system 

configuration must be performed before installation.   

4.3.1 AT/ATX Power Mode Setting 

The AT and ATX power mode selection is made through the AT/ATX power mode switch 

which is shown in 

Figure 4-9

. 

 

 

Figure 4-9: AT/ATX Power Mode Switch Location 

Summary of Contents for IMB-Q870-i2
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands