manualshive.com logo in svg

IEI Technology IMB-Q870-i2, User Manual

Share
Download
IEI Technology IMB-Q870-i2 User Manual Download Page 87

 

 

IMB-Q870-i2 microATX Motherboard 

Page 71

 

Figure 4-16: HDMI Connection 

 

Step 3: 

Insert the HDMI connector.

 Gently insert the HDMI connector. The connector 

should engage with a gentle push. If the connector does not insert easily, check 

again that the connector is aligned correctly, and that the connector is being 

inserted with the right way up. 

Step 0:

 

4.5.4 LAN Connection 

There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection 

to an external network. To connect a LAN cable with an RJ-45 connector, please follow 

the instructions below. 

Step 1: 

Locate the RJ-45 connectors

. The locations of the USB connectors are shown 

in 

Chapter 3

. 

Step 2: 

Align the connectors. 

Align the RJ-45 connector on the LAN cable with one of 

the RJ-45 connectors on the IMB-Q870-i2. See 

Figure 4-17

. 

Summary of Contents for IMB-Q870-i2
































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands