IEI Technology IMB-Q870-i2 User Manual Download Page 173

Page: 173 / 223

IMB-Q870-i2 microATX Motherboard

Page 157

After completing the five initial setup procedures as described above, users can access

the recovery tool by pressing <

> while booting up the system. The detailed information

of each function is described in

Section C.5

NOTE:

The initial setup procedures for Linux system are described in

Section C.3

C.1.1 System Requirement

NOTE:

The recovery CD can only be used with IEI products. The software will

fail to run and a warning message will appear when used on non-IEI

hardware.

To create the system backup, the main storage device must be split into two partitions

(three partitions for Linux). The first partition will be for the operating system, while the

second partition will be invisible to the operating system and contain the backup made by

the one key recovery software.

The partition created for recovery images must be big enough to contain both the factory

default image and the user backup image. The size must be calculated before creating the

Summary of Contents for IMB-Q870-i2
































































































































































































































Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands

IEI Technology IMB-Q870-i2, User Manual

Search results

Summary of Contents for IMB-Q870-i2

Reviews:

Related manuals for IMB-Q870-i2

Brands by name

Popular brands