1-11
1
PANEL DESCRIPTION
o
MULTIFUNCTION SWITCH GUIDE
Indicates the function of the multifunction switches.
!0
LCD FUNCTION SWITCH GUIDE
Indicates the function of the LCD function switches
([F-1] – [F-7]).
!1
MULTIFUNCTION SCREEN
Shows the screens for the spectrum scope, voice
recorder, memory channel list, scan, FSK decoder,
IF filter selection or set modes, etc.
!2
TUNING STEP INDICATOR
(p. 3-5)
Shows the selected tuning step.
!3
1/4 FUNCTION INDICATOR
(p. 3-6)
Appears when the 1/4-speed tuning function is acti-
vated in CW and FSK modes.
!4
AUTOMATIC TUNE INDICATOR
(p. 5-17)
“
”blinks during automatic tuning. This
feature is active in AM, SSB and CW mode.
!5
MEMORY CHANNEL INDICATOR
(p. 7-3)
Indicates the selected memory channel number.
!6
TUNING DIGIT INDICATOR
(p. 3-5)
Shows the tuneable digit when rotating the main
dial.
!7
TONE/DTCS/NAC/SELECTIVE SQUELCH
INDICATOR
➥
“TSQL” or “DTCS” appears when the tone
squelch or DTCS squelch is set in FM mode.
(p. 4-4)
➥
“NAC” or “SEL” appears when the NAC squelch
or selective squelch is selected in P25 mode.
(Requires optional UT-122.) (p.4-19)
!8
BANK INDICATOR
(p. 7-3)
Appears when the bank limit function is in use and
indicates the selected bank number.
• BANK-0 to BANK-9, BANK-A (AUTO MW), BANK-S
(SKIP) and BANK-P (SCAN EDGE) are selectable.
!9
NOISE BLANKER INDICATOR
(p. 5-15)
“NB1” or “NB2” appears when either noise blanker 1
or noise blanker 2 is ON. This function is not avail-
able for FM/WFM or P25 mode.
@0
CF CARD/USB-MEMORY INDICATOR
(p. 11-16)
➥
“
” appears when CF card is correctly con-
nected and blinks while CF card is active.
• This indicator is normally stayed ON.
➥
“
” appears when USB equipment (USB-
Memory or keyboard, etc) is connected, and
blinks while it is active.
@1
CLOCK READOUT
(p. 10-2)
Shows the current time. Local and UTC time can in-
dicate at the same time.
@2
NOISE REDUCTION INDICATOR
(p. 5-16)
Appears when noise reduction function is in use.
@3
BANDPASS FILTER INDICATOR
Appears when the narrow filter (500 Hz or less) is
selected during CW or FSK operation.
@4
PASSBAND WIDTH INDICATOR
(p. 5-11)
Graphically displays the passband width for twin
PBT operation and center frequency for IF shift op-
eration.
@5
AUDIO PEAK FILTER INDICATOR
(p. 4-10)
Appears when the audio peak filter function is in use.
This function is available in CW mode
@6
SHIFT FREQUENCY INDICATOR
(p. 5-11)
Shows the shift frequency of the IF filter.
@7
NOTCH FILTER INDICATOR
(p. 5-16)
➥
“
” appears when the auto notch function is in
use. This function is available in FM, WFM, AM
and SSB modes.
➥
“
” or “
” appears when the manual notch
filter function is in use. This function is available in
AM, SSB, CW and FSK mode.
@8
BAND WIDTH INDICATOR
(p. 5-11)
Shows the passband width of the IF filter.
@9
DUPLEX INDICATOR
(p. 4-3)
“DUP–” or “DUP+” appears when the negative duplex
or positive duplex operation is selected, respectively.
MN2
MN1
AN
USB
CF
AUTO TUNE
