Hyundai HI RUN n 700 Instruction Manual Download

Page: 39 / 186

N700 Operating Instructions and Parts Manual

2. Installation and Wiring

⑥

When a relay is used as an intelligent output, connect a diode for surge protection parallel

to the relay coil.

⑦

Do not short the analog voltage terminals H and L or the internal power terminals PV24

and all CM1’s. Otherwise there is risk of Inverter damage.

⑧

When connecting a thermistor to the TH and all CM1’s terminal, twist the thermistor

cables and separate them from the rest. Limit the connection wires to 65 feet.

(3) Change of input logic type

The logic type of intelligent input terminals is on the following list (Factory Default).

N700 Inverter(5.5

㎾

~ 132

㎾

) Sink

TYPE

The input logic type can be changed by changing the Short bar connection of control terminal.

Sink type

Between P24 and PLC on the control terminal.

Source type

Between PLC and CM1 on the control terminal.

(4) The connection to the input programmable logic controller (sequencer)

To use interface power within inverter

To use outside power

(Remove the short bar off of the control

terminal.)

Sink T

Source T

Summary of Contents for HI RUN n 700



























































































































































































Search results

Summary of Contents for HI RUN n 700

Reviews:

Related manuals for HI RUN n 700

Brands by name

Popular brands

Hyundai HI RUN n 700, Instruction Manual

Search results

Summary of Contents for HI RUN n 700

Reviews:

Related manuals for HI RUN n 700

Brands by name

Popular brands