Hyundai HI RUN n 700 Page 159 Instruction Manual Download

Page: 159 / 186

N700 Operating Instructions and Parts Manual

12. Explanation of H-Group

138

Motor connection

Auto-tuning mode selection

H001=1 or 2

RUN command ON

Motor parameter setting

①

DC excitation (no ratation)

②

AC excitation (no ratation)

③

V/F operation (For H001=1, no rotation)

④

Display the tuning result

Parameter setting

completed, stop

End display

Fig. 12- 2 Autotuning procedure

12.2.2 ON-LINE

autotuning

(1) Online autotuning can revise the motor constant by increase of temperature, and stabilize

running.

(2) This function acts only the 1st motor control. Do not operate it in the 2nd motor control.

(3) Precautions

①

Be sure to execute offline autotuning before executing online autotuning.

②

Be sure to execute autotuning once when a general-purpose motor, as the data for online

autotuning is computed during offline autotuning.

③

If DC braking is set when the motor stops, online autotuning is executed after DC braking

operation terminates.

(4) Setting

method

①

Set the motor constant selection (H002/H202) to the data of autotuning that is valid 2(AT

ONLINE DATA) online tuning.

(Give the autotuning selection (H001) as the ineffectiveness (0).)

②

Input the run command.

12.3

Sensorless vector control(SLV)

(1) This function is the method that the revolution of motor and output torque are estimated by

output current, voltage of the inverter and motor constant of setting. It is possible to operate

high starting torque and high accuracy at low frequency(0.5Hz).

(2) In the case of using this function, please set 5(SLV) in F012.

(3) In the case of using this function, please set surely the suitable motor constant of using the

motor according to the parameter of “selection of motor constant [H**]”.

(4) Precautions

①

If the inverter operates less than two steps in capacity level for the maximum adopted

motor, the full performances may not be demonstrated.

②

If a satisfactory performance can not be obtained, please adjust the motor constant for the

phenomena according to the following table.

Summary of Contents for HI RUN n 700



























































































































































































Search results

Summary of Contents for HI RUN n 700

Reviews:

Related manuals for HI RUN n 700

Brands by name

Popular brands

Hyundai HI RUN n 700, Instruction Manual

Search results

Summary of Contents for HI RUN n 700

Reviews:

Related manuals for HI RUN n 700

Brands by name

Popular brands