Hyundai HI RUN n 700 Page 148 Instruction Manual Download

Page: 148 / 186

N700 Operating Instructions and Parts Manual

11. Explanation of C-Group

127

releasing signal is outputted, the inverter will not accelerate until the braking confirmation

which is set in (C016). If braking confirmation signal is not inputted within waiting time for

braking confirmation, the inverter will output braking error signal (BER) and would occur

the trip. If braking confirmation signal is not set to intelligent input braking terminal, the

waiting confirmation will be invalid, and after the inverter will output braking releasing

signal, proceed to

④

After braking confirmation signal is inputted(after braking releasing signal is outputted

when BOK is not selected), the inverter waits for acceleration, and then begins to

accelerates again and accelerates to the frequency.

⑤

When running command turns off, the inverter decelerates to releasing frequency and

turns braking releasing signal (BRK) off.

⑥

When braking confirmation signal (BOK) is set to intelligent input terminals, after braking

releasing signal turns off, the inverter will not decelerate during the waiting time for

braking confirmation which is set in (C016), and will wait for braking confirmation signal to

turn off.

If braking confirmation signal does not turn off within the waiting time for braking

confirmation, the inverter will output braking error signal (BER) and the trip will occur.

If braking confirmation signal is not set to intelligent input braking terminal, the waiting

time for braking confirmation will be invalid and after the inverter will output braking

releasing signal, proceed to

⑦

After braking confirmation signal turns off (after braking releasing signal turns off), the

inverter waits for the waiting time for stop, and then begins to decelerate again and

decelerates to 0 Hz.

C017 break releasing

frequency

Output frequency

Running
command

Braking releasing
output

Braking confirmation
signal

C015 waiting time for stop

C013 waiting time for conformation

C014 waiting time for
acceleration

C016 waiting time for braking

confirmation

C016 waiting time for braking

confirmation

C017 releasing frequency

⑦

②

④

③

⑥

Fig. 11- 4 Timing chart that BOK is selected to intelligent input terminals.

(2) When braking control function is used, if necessary, assign the following functions to

intelligent input/output terminals.

①

When signal outputted from external braking during releasing braking is inputted to an

inverter, one of the intelligent output terminals should be assigned braking conformation

signal: BOK(33).

②

One of the intelligent output terminals should be assigned to braking signal : BRK to

release braking.

And when output signal at the time of braking trouble is used, signal of braking trouble :

BER should be assigned.

Summary of Contents for HI RUN n 700



























































































































































































Search results

Summary of Contents for HI RUN n 700

Reviews:

Related manuals for HI RUN n 700

Brands by name

Popular brands

Hyundai HI RUN n 700, Instruction Manual

Search results

Summary of Contents for HI RUN n 700

Reviews:

Related manuals for HI RUN n 700

Brands by name

Popular brands