Hunter Douglas Douette PowerView Installation Operation Care Download Page 18 | Manualshive

Page: 18 / 44

background image

INSTALLATION

16

■

■

Inside Mount:

Attach the stationary rail bottom bracket. The bracket may be attached to the

sill or floor. It may also be attached to the jamb using the inside mount adapter.

■

➤

Be sure the stationary rail is flush against the jamb.

■

➤

Floor or sill attachment:

Attach the stationary rail bottom bracket using the screw

provided.

■

➤

Jamb attachment:

Use the inside

mount adaptor to secure the
stationary rail to the side of the jamb.

— Slide the inside mount adaptor

onto the stationary rail bottom

bracket. Align the screw hole of

the adaptor to face the side jamb

(or side wall).

— Secure with the provided screw

through the inside mount adaptor

and into the side jamb (or side

wall).

NOTE:

If you ordered your shade with a cut-out, for baseboards or other obstructions, you

must use the inside mount adaptor.

CAUTION:

Use drywall anchors when mounting into drywall.

Inside Mount

Adapter

Stationary

Rail Bottom

Bracket

Stationary

Rail Bottom

Bracket

Floor or Sill Attachment

Jamb Attachment

Jamb

Attachment

«
...
16
17
18
19
20
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: Gami Pages: 4

Brand: feather&black Pages: 4

Brand: pakoworld Pages: 6

San Fran 2 Person Run Workstation

Brand: Jason.L Pages: 4

Brand: Samson Pages: 8

Japanese Myojin Style Torii Gate

Brand: SAMSGAZEBOS Pages: 7

Brand: TDK Pages: 2

Brand: TDC USA Pages: 9

Capitola SEA8031-Q

Brand: Safavieh Furniture Pages: 2

Brand: ABSCO SHEDS Pages: 14

Brand: Walker Edison Pages: 26

Brand: DHP Pages: 25

Brand: HULALA HOME Pages: 5

Brand: RiverRidge Pages: 20

Brand: Tresanti Pages: 12

Brand: Camaflexi Pages: 13

Ameriwood Industries 3572207PCOM

Brand: Dorel Pages: 20

Brand: Furniture of America Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands