Hunter Douglas Douette PowerView Installation Operation Care Download Page 2 | Manualshive

Page: 2 / 44

background image

CONTENTS

Getting Started:

Product View ................................................................ 1
Tools and Fasteners Needed .......................................... 2
Valance Types ............................................................... 3
Installation Brackets Required ........................................ 3

Installation:

Installation Overview ..................................................... 4
Outside Mount Installation ............................................. 5

Mount the Installation Brackets .................................. 5
Mount the Headrail .................................................... 8

Inside/Ceiling Mount Installation ..................................... 9

Mount the Installation Brackets .................................. 9
Mount the Headrail .................................................. 10

Install the Fabric Stack ................................................ 11

Prepare the Fabric Stack ......................................... 11
Install the Fabric Stack into the Headrail ................... 12
Set Cord Tension ..................................................... 17

Mount the PowerView

™

Manual Control Button ............. 22

Connect the Power Source .......................................... 24

Battery Wands ........................................................ 24
DC Power Supply .................................................... 26

Operation:

Testing the Shade ....................................................... 27
Using the PowerView Remote ...................................... 27
Resetting the Shade (If Necessary) ............................... 28
Dual Operation ............................................................ 29

Valance Installation:

Valance Attachment .................................................... 30

Attach Valance Clips ................................................ 30
Aluminum Valance .................................................. 31
Alternative Wood Valance ......................................... 33

Room Divider Installation ............................................. 34

Care:

Troubleshooting .......................................................... 35
Removing the Shade (If Necessary) .............................. 38
Cleaning Procedures ................................................... 38

Declarations

.............................................................. 40

Warranty

.........................................................Back Cover

Questions?

Call the Hunter Douglas Customer Information Center at

1-888-501-8364.

© 2016 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas

or their respective owners.

«
1
2
3
4
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: Habitat Pages: 8

Brand: Vamo Pages: 3

Brand: Yaasa Pages: 200

Brand: Ameriwood HOME Pages: 29

Frame 119-000814

Brand: homitis Pages: 16

Brand: Next Pages: 19

Brand: Courtyard Creations Pages: 4

Brand: Courtyard Creations Pages: 2

Brand: Zanzini Pages: 4

Brand: Vector Pages: 15

Brand: Vitea Care Pages: 10

Brand: Walker Edison Pages: 16

Brand: Next Pages: 17

Brand: Seville Classics Pages: 4

BLACK WOOD GRAIN LISBON

Brand: Seconique Pages: 9

The Coffee Table

Brand: neighbor Pages: 8

Brand: KayserBetten Pages: 24

Brand: Ameriwood HOME Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands