Hunter Douglas Douette PowerView Installation Operation Care Download Page 20 | Manualshive

Page: 20 / 44

background image

INSTALLATION

18

■

■

Study the cording diagram below. The cords are connected to the end plate that is opposite
the fabric stack. (In the illustration, the two cords are shaded differently to make the routing
easier to follow.)

■

➤

One of the washers is anchored to the end plate in the middle slot. The cord is routed
under the end plate and into the slot so that the washer is on the inside of the end plate,
as shown.

■

➤

The washer on the other cord is trimmed off and the end is tied to the cord tensioner.
Then that cord is looped around the “T” near the front of the end plate.

IMPORTANT:

The top of the looped cord must be the portion of the cord coming from the

cord tensioner.

Cord

Tensioner

Moving

Rail

End

Plate

End Plate

Front

Rear

Cord with

Washer

Cord with

Washer

To Cord

Tensioner

«
...
18
19
20
21
22
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: Xo Pages: 5

Brand: Safco Pages: 2

Brand: MAJA Möbel Pages: 8

Brand: OAK Pages: 2

Brand: LaGrand Pages: 2

Brand: Landscape Forms Pages: 2

Brand: Rauch Pages: 34

Brand: HAMPTON BAY Pages: 9

Brand: µ-Dimension Pages: 5

Brand: Gautier Pages: 12

Brand: Okamura Pages: 4

Brand: MAAX Pages: 16

Brand: Amerihome Pages: 2

Bowfield 315900KE

Brand: Coaster Pages: 6

Lisbon LISBON7PC-TAN

Brand: Hanover Pages: 9

SELECT GRANDSTAND

Brand: felton industries Pages: 2

ZIPCODE DESIGN 13PW152WHT

Brand: Wayfair Pages: 5

Brand: Quoizel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands